OpenAVL has no built-in unit system. Enter every dimensional value in one consistent set, for example SI (m, kg, s): velocity in L/T, density in M/L³, gravity in L/T², mass in M, inertia in M·L². Geometry lengths are in the units of the .avl file; a mass file's Lunit converts them to the mass-file length unit for dimensional results. Here L, M and T stand for your length, mass and time units.
Reference values and flight condition
| Quantity | Definition | Units |
| Dynamic pressure | q = ½ ρ V² | M/(L·T²) |
| Sref, Cref, Bref | Reference area, chord and span from the .avl header | L², L, L |
| Aspect ratio | AR = Bref² / Sref | none |
| Mach number | M = V / a, Prandtl–Glauert factor √(1 − M²). Valid for 0 ≤ M < 1. | none |
| α, β | Angle of attack and sideslip | deg |
| Moment reference | All moments and derivatives are taken about the CG (Xcg, Ycg, Zcg) | L |
Force and moment coefficients
Total Forces and Surface Forces panels. Lower-case cl, cm, cn in Total Forces are the moment coefficients.
| Quantity | Definition | Units |
| Lift, drag, side force | CL = L / (q Sref), CD = D / (q Sref), CY = Y / (q Sref) | none |
| Roll moment | Cl = ℓ / (q Sref Bref) | none |
| Pitch moment | Cm = M / (q Sref Cref) | none |
| Yaw moment | Cn = N / (q Sref Bref) | none |
| Drag breakdown | CD = CDi + CDp. CDp is profile drag: CD0 plus any CDCL polars. CDi is the rest. | none |
| Span efficiency e | e = (CL² + CY²) / (π AR CDi), using Trefftz-plane (far-field) values | none |
Non-dimensional rates
In Total Forces and the Body Axis Derivatives table, p, q, r are body-axis rates in rad/T. Rate rows in Constraints and the Stability Derivatives table use stability-axis roll and yaw rates p′, r′, as AVL does: the body rates rotated by α about Y (q is the same in both). They differ when α ≠ 0.
| Quantity | Definition | Units |
| Roll rate | p̂ = p Bref / (2V) | none |
| Pitch rate | q̂ = q Cref / (2V) | none |
| Yaw rate | r̂ = r Bref / (2V) | none |
Derivatives
The 1/rad – 1/deg selector on Stability Derivatives applies to every derivative panel: (1/deg) = (1/rad) × π/180. It changes only the angle derivatives; rate derivatives are already non-dimensional.
| Quantity | Definition | Units |
| Angle derivatives (α, β columns) | CXα = ∂CX / ∂α, CXβ = ∂CX / ∂β | 1/rad or 1/deg |
| Rate derivatives (p, q, r columns) | CXp = ∂CX / ∂p̂, CXq = ∂CX / ∂q̂, CXr = ∂CX / ∂r̂ | none |
| Body-axis u, v, w rows | ∂C / ∂(u/V), ∂C / ∂(v/V), ∂C / ∂(w/V). v/V ≈ β and w/V ≈ α, so the v and w rows follow the unit selector. | none u; 1/rad or 1/deg v, w |
| Control derivatives | ∂C / ∂δ for each control deflection δ | 1/rad or 1/deg |
| Control deflections | Trimmed δ shown under Total Forces | deg |
| Neutral point Xnp | Xnp = Xcg − (Cmα / CLα) Cref | L (.avl units) |
Dimensional outputs
These use ρ, V, mass and inertia, with Sref, Cref and Bref scaled by Lunit.
| Quantity | Definition | Units |
| Forces and moments | F = q Sref CF, ℓ = q Sref Bref Cl, M = q Sref Cref Cm, N = q Sref Bref Cn | M·L/T², M·L²/T² |
| ax, ay, az | a = F / m, aerodynamic force only, body axes | L/T² |
| pdot, qdot, rdot | I ω̇ = M − ω × (I ω), body axes | rad/T² |
| Hinge moment coefficient | Ch = H / (q Sref Cref) | none |
| Hinge moment | H = Ch q Sref Cref. Shown only when ρ and V are not both 1. | M·L²/T² |
Eigenmodes
Eigenanalysis panel and plot. Needs dimensional ρ, V, g, mass and inertia.
| Quantity | Definition | Units |
| Eigenvalue (Real, Imag) | λ = σ + iω | 1/T |
| Frequency | f = |ω| / (2π) | Hz when T = s |
| Period | T = 1 / f | T |
| Time to half amplitude T½ | t½ = ln 2 / |σ|, decaying modes (σ < 0) only | T |
Plots and 3D viewer
| Quantity | Definition | Units |
| Trefftz: cl | Strip lift coefficient, cl = L′ / (q c), with L′ lift per unit span and c the local chord | none |
| Trefftz: cl⊥ | cl⊥ = cl (V / V⊥)², with V⊥ the velocity normal to the strip's spanwise axis (sweep-corrected) | none |
| Trefftz: cl c / cref | Span loading, cl c / Cref | none |
| Trefftz: αi | Induced angle in the Trefftz plane | rad |
| Viewer: ΔCp | ΔCp = Δp / q, the pressure jump across each panel (lifting load) | none |
Axis systems
| System | Directions | Used for |
| Geometry axes | X aft (downstream), Y right, Z up | Coordinates in the .avl file, CG location, Xnp, the 3D viewer and the Trefftz span axis y |
| Body axes | X forward, Y right, Z down. The X and Z components of geometry-axis values change sign. | Total Forces moments (cl, cm, cn), rates, accelerations, Body Axis Derivatives |
| Stability axes | Body axes rotated by α about Y, so X lies along the freestream projected on the symmetry plane | CL, CD, Stability Derivatives, Control Surface Derivatives (Stability) |
Positive directions
| Quantity | Positive when |
| α | Freestream comes from below (nose up relative to the flow) |
| β | Freestream comes from the pilot's right |
| p, Cl | Right wing down |
| q, Cm | Nose up |
| r, Cn | Nose right |
| Control deflection δ | Right-handed rotation about the hinge vector given in the .avl CONTROL line |