NetAna Documentation

NetAna is a program developed to solve sets of linear equations using matrix algebra to solve electrical network voltage and current values. Python, and Python-Matplot were used to create the multi-platform program. The GUI was handcrafted using Python's built in Tkinter.

NetAna can analyze DC and AC networks using either Node or Mesh equations. NetAna uses a network specification (component values) and driving voltages or currents and in the case of an AC network the frequency range. Any text editor can be used to create, edit, and save the network specification file. The "spec." file must be saved with an ".txt" extension. Once the specification filename is selected, the network equations are entered into a matrix (grid table). This matrix is “Submitted”, stored in a file. The network is then analyzed producing an analysis report displayed in a pop up window. Next a plot of the gain and phase angle can be produced. This plot can also be saved to a file providing the user with a complete report and plot for documenting the performance of the network.

NetAna Documentation
- Program Reserved Keywords
- Keyword Usage
  - - NODES
    - MASHS
    - VG
    - IG
    - L*
    - C*
    - R*
    - VGLIST
    - IGLIST
    - FREQ
    - TF
    - GOALS
    - GOAL?
- Program Usage
- Plot Network Report
- Net Connection List

Program Reserved Keywords

The following words/symbols are used in defining the network/circuit specification. The specification in typed into the program editor or your favorite text edited and saved with the ".txt" extendsion. The specificatioon may be typed in either lowercase or uppercase. Python is case senesitve but, this program scans the specification file and converts the text to uppercase before evaluating the specification. The reserved words below are shown in upper case even though they can be entered in lower case.

NODES	MASHS	VG	IG	L*
C*	R*	VGLIST	IGLIST	FREQ
TF	GOALS	GOAL?

Keyword Usage

NODES

This word is required to be defined for node analysis and specifes the number of nodes in the network. Example "nodes = 5" to specify a five node network.

MASHS

This word is required to be defined for mash analysis and specifes the number of mashs in the network. Example "mashs = 4" to specify a four mash network.

VG

This word defines the voltage generator value when doing mash analysis. When 'VG' is used. the program will do mash analysis. Example "VG = 10.0' will specify a 10.0 volt generator.

IG

This word defines the current generator value when doing node analusis. When 'IG' is used, the program will do node analysis. Example: "Ig = 0.500' will specify a 500 millampere current generator.

L*

L must be the first character of a word to define an inductor value. Normaly the usage would be ",L1, L2, L3, L4 ......... " or "l1, l2, l3, l4 .... " but, the usage of the lower case L may be confused for the number 1. Example: L23 = 25.0e-3 ( 25.0 millihenry )

C*

C is the first character of a value defination for a capacitor - see above L* for usage. Example: c1 = 0.1e-6 ( 0.1 microfarad )

R*

R must be the first character of the word to define resistor values. Examples: r1 = 10e3 , R2 = 10,000.0, r4 = 1e6, R3=2*R2 where values are in ohms.

VGLIST

Used to define mulitple voltage sources (mash analysis). Example: vglist = [e1, e2, 0, 0, e2]
This defines two voltage sources driving three mashs ( mashs 1, 2, and 5) where mashs are the current loops.
The first element of the list is the voltage source for meash 1. In the above 'vglist' voltage 'e2' is driving mash 2 and 5.

IGLIST

Used to define muliple current souces (node analysis). Example: iglist = [i1, i2, 0, 0, 0, e1*y3]
This defines three current souces in a six node network. Current source at node six is the product of voltage e1 and admittance y3.

FREQ

This keywork is used when doing AC analysis olny. It defines the 'start, stop, increment, label' frequency range that will be used in the analysis.
Example: FREQ=(100,500,10, "Hz") defines a frequenci range starting at 100 Hz to 500 Hz in steps of 10 Hz. And defines the frequency label used the label the response plot.

TF

The 'TF' (Transfer Function) keyword is used the define the output of the analysis program. Example; TF = ("(i2-i3) * R3", "Volts") defines, for mash analysis, the voltage across resistor R3. During analysis all mash currents are solved and during node anlysis all node voltage are solved. The second parameter passed to the TF is a label, used for DC analysis only, used in writing the output report. If in the above example the output to be in millivolts instead of volts, the TF is written as TF = ("(i2-i3)*R3*1e3"," mv") note that the first parameter must be scaled by 1e3 (1000) to get millivolts.

GOALS

The GOALS keyword is only used in DC analysis. It defines the number of goals, simalar to transfer functions. Example: GOALS=3 specifies that there are three output goals or expressions to be solved for using the network elements, currents, or voltages. During Mash Analysis all loop currents are solved and during Node Analysis all node voltages are solved.

GOAL?

GOAL? means Goal1......GoalN. where N is defined by keywprd GOALS above.
Assuming Node Analysis:

Example: Goal1 = ("(e1-e2) / R2 * 1000", "ma.") # find current in R2

Goal2 = ("e1-e2", "volt") # find voltage across R2 assuming R2 connected between nodes 1 and 2.

Program Usage

Once the program is running, a frame with a top menu bar and four buttons will be visible to the user. Depress the "Enter Sepc. File Name" button and select the "Spec." file. The 'spec' (specification) file is a plain text file with an extension '.txt' that contains the program keywords. See the included Demo files in the 'Examples' folder included with this distribution.

Next depress the 'Enter Network Equations' buton. A zero filled grid (table) will appear if this is the first analysis run of this network. Fill in the grid with the network equations. The equation cells in the grid are unique in that no 's' or 'jw' symbols are entered in the cells, only componet symbols. The reactances are computed by the program. Therefore, all the capacitor and inductance symbols must be entered with their C's and L's. If this network has been analyzed before, the grid wll come up with the network equations already entered as used in the last run. The equation can be edited any time this grid frame is open. When all equations have been entered, depress the 'Submit' button on the grid dialog frame. This will save the equations in a file with an '.equ' extension.

Note: A feature has been added to version 1.0.0 alowing the user to specify the network equations and connections in a xxxxx.net file documented below.

Once the equations have been saved as above, the 'Analize Network' should be pressed. If all goes well a new window will pop up displaying the output report data. When doing DC analysis the report will show all the loop current values for Mash analysis plus any GOAL values or all the node voltage values plus GOAL values when doing Node Analysis.

When doing AC Analysis the report will show the TF, transfer function, magnitude and phase values verses frequency as defined by the FREQ specification.

Once a network/circuit has been analyzed three files will be created and maybe an optional forth file may be created. These three files should be kept together in order to make rerunning the analysis with the same 'spec' and equations.

mynetwok.txt -- user input 'spec' file
mynetwork.report -- program generated output response file
mynetwork.equ -- equation file
mynetwork.net -- optional connection list file
xxxxx.png -- plot image file, you apply name as you save it.

Plot Network Report

After viewing the output report, the output may be ploted by depressing the 'Plot Network Report' button. You may save the plot by depressing the lower right button on the plot frame. If you want to print either the saved report or plot files, use one of the standard printing methods, depending on the computer platform being used.

Net Connection List

Version 1.0.0 has added a feature that allows te user to creat a network connection text file that will be used to fill in the grid when the "Enter Network Equations" button is depressed if the ".equ" file does not exist.

An example of a connection file is shown below for the "BainterFilter":

When entering data in the first data column be sure to include the symbols for the reactive components. The reactive component must be exposed (shown). Data may be entered in either upper or lower case.
Example: R1 is in series with C1; Y1 = 1.0/R1 + C1 and Y1 is connected between node 4 and 5
DO NOT define a connection line as: Y1,4,5 instead define as: 1.0/R1+C1,4,5
When creating this .net file you can create a comment using the "#" symbol any place in the line and the rest of the line will be treated as a comment. The xxxxxxx.net file will only be used if an xxxxxx.equ file does not exist. If you depress the "Save" button in the Equation Dialog grid display the equation imformation will be saved in the xxxxxx.equ file. As long as the xxxxxxx.equ file exists, the xxxxxxxx.net file will not be used.